banner



How To Install Swanstone Sink Clips

The kitchen sink is an essential element of any household. Food is prepared, dishes are washed, flower vases are filled, and food is disposed of in the kitchen sink. The kitchen sink can exist installed to a higher place the counter, below the counter, or even every bit a seamless role of the counter itself.

Want to install a kitchen sink? This expert guide will take you through the process step-by-pace.

To many homeowners, installing a kitchen sink seems like a daunting chore, but the fact is, if you lot tin can trace effectually a template and cutting out a pigsty, y'all tin install a kitchen sink.

install a kitchen sink
Installing a kitchen sink in a plastic laminate countertop is a relatively easy task.

You lot do want to make sure your new sink fits your countertop and the cabinet below it, and so mensurate the width and depth of your lower cabinets before making a purchase.

Generally, a sink upwards to 22 inches deep (from front end to back) volition fit in a standard 24-inch-deep cabinet if you accept no backsplash; if you lot do have a backsplash, your countertop will only take a sink upwards to 20 ane/two inches deep. Of course, your options will increment if you are as well irresolute your cabinetry and countertop.

Install a Drib-In Kitchen Sink: Step-by-Step

To install a counter-superlative kitchen sink, follow the directions below:

+

Find Pre-Screened Plumbers Near You

1 The starting time step when installing a new sink is to properly site the opening. Most sink manufacturers provide a template.

Position the template then it is centered on the sink cabinet and is at least 1 1/2 inches back from the countertop's front border. If your countertop is deeper than 24 inches, place information technology farther back, merely not more than iv inches. Tape the template in place, so outline it with a marker.

installing a kitchen sink
Lay the sink's template on the countertop and mark for the cutout.

2 After marking the opening, remove the template and drill a iii/8-inch-bore hole in each corner.

Insert a saber-saw blade in ane of the holes and get-go cutting along the inside of the line. To prevent the cutout from snapping off and falling through as y'all complete the cuts, get-go spiral a chip of forest from forepart to dorsum on the superlative of the cutout long enough so it spans the opening, plus a couple of inches.

When you've finished, merely lift the cutout from the template.

cutting template area
Use a saber saw to cut out the template area.

three Install the faucet (see How to Install a Kitchen Faucet for instructions) and the sink strainers. (Doing this when you've got full admission to the sink will be much easier than fitting the pieces in from below later on the sink is installed.)

Next, to create a watertight seal between the sink and the countertop, apply a dewdrop of silicone caulk or plumber's putty effectually the unabridged perimeter of the underside of the sink's lip.

caulking a kitchen sink
Seal the underside of the sink's flange before setting the sink in identify.

4 Carefully flip the sink over and insert into the opening, taking care not to disturb the caulk or putty.

Now install the kitchen sink. If your sink is heavy, get assist lifting and installing it; too consider placing a couple of scraps of wood near the edge of the opening to back up the sink and protect your fingers as you drop it into position.

installing a kitchen sink
Later on installing the faucet onto the sink, position the aggregation in the cutout.

5 Virtually sinks are pulled downwardly tight against the countertop with special mounting clips that hook onto the lip on the underside of the sink and are tightened with a screwdriver or nut-driver. Follow the manufacturer'south directions for spacing these clips.

Tightening the mounting clips may cause the caulk or putty to squeeze out from nether the sink lip, so remove this excess with a clean, soft rag.

securing kitchen sink
Secure the underside of the sink to the countertop past tightening the bolt clips.

6 To complete the project, first connect the P-trap. Join the faucet lines to the hot and cold supply lines with flexible supply tubes and connect the strainers to the waste line.

Turn the h2o on at the close-off valves, remove the aerator from the faucet, then plough on the h2o from the faucet to flush the system. Reinstall the aerator later on you've run the h2o for a minute or so.

installing drain trap
Install the P-trap beneath the sink and the water supply tubes to the faucet.

Install a Drop-In Kitchen Sink Video

This video walks you through the steps of installing a drop-in kitchen sink.

Install an Under-Mount Kitchen Sink Video

Installing an under-mount kitchen sink is quite every bit easy as installing a drib-in sink. Nevertheless, this video shows you how:

Featured Resource: Become a Pre-Screened Local Sink Installation & Plumbing Pro

Telephone call for complimentary estimates from local pros now:
one-866-342-3263

Source: https://www.hometips.com/diy-how-to/install-kitchen-sink.html

Posted by: geterintentookey1948.blogspot.com

0 Response to "How To Install Swanstone Sink Clips"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel